거꾸로 타는 실내용(캠핑) 난로 아직 못 만들었어요..?ㅣ각파이프 DIYㅣ실내용(텐트) 스토브 만들기ㅣ휴대용 겨울 캠핑난로ㅣ각관스토브ㅣ우드스토브(로켓스토브)ㅣ오븐스토브ㅣ불멍ㅣDIY

00:16 - However, when using a firewood stove inside tents and shelters during winter camping I sometimes hesitate because of risk factors such as suffocation or fire.

00:26 - To keep camping warm and safe even in cold winter Second to the ashtray, trash, inner stove Again, I tried to make it using ready-made materials that can be easily obtained from the surrounding area.

00:38 - Key production factors include maintaining warmth with high heat preservation rate and various delicious dishes that are indispensable for camping.

00:50 - Hello Space where creative tools are collected with reason to know yourself and endless sensibility ‘Whiscovery’ is our discovery.

00:58 - Before making, let’s take a look at the principle of each pipe inner stove.

01:02 - The fire of firewood meets oxygen sucked in through the only firewood entrance Helps the firewood to keep burning The hot flame is discharged into the pipe through the flame of the inner stove The winding structure of each pipe helps the warm heat to stay for a long time.

01:20 - The purpose of this new pipe inner stove is to maximize thermal efficiency and to effectively discharge carbon monoxide generated by burning firewood.

01:26 - In addition, to increase efficiency, we plan to build an oven that can cook various dishes using the heat of the inner stove for each pipe.

01:36 - This is a 125mm square pipe You can buy it easily for a small fee First, I’m going to pierce the flame in the first pipe Uh, these pants and jackets have holes Today’s work doesn’t end here.

02:12 - Change clothes and start shooting again Make a hole for flame in the first angle pipe You can also make a hole in the part that contacts the first angle pipe It is important to drill smaller than the flame hole of the first angle pipe.

02:46 - It is for the convenience of welding work and to meticulously block smoke.

02:56 - The second angle pipe has two holes Make an additional hole to connect with the third angle pipe. I am going to make a hole in the part where the third angle pipe is in contact with the second.

03:34 - The angle pipes are similar, so I marked them with a grinder.

03:46 - I drilled an additional hole to connect the third and fourth pipes In the middle, I also check to see if it’s right as I thought After roughly drawing guidelines on the fourth angle pipe Mark and pierce it I also drilled an additional hole to connect to the fifth angle pipe Now, mark the fifth angle pipe that will pierce the last flame and make a hole Let’s set a spot for the flames to pass I’m going to use this as an oven so I didn’t drill a hole It fits well.

06:08 - Next, it’s time to do the welding on the abutting parts in order. Because welding is unfamiliar, there may be some inconvenient parts for experts.

06:10 - We need to weld thoroughly so that the smoke does not leak out.

06:20 - I put all the angle pipes together We plan to prevent smoke from leaking out with this iron plate.

07:02 - One two three four five six seven eight nine Throw away the padding and cut it according to the guideline like crazy.

07:34 - Hannome Dusik Seoksam Raccoon Squid Yukgaejang Chilchil Eight Commandments Gugudan Ten Commandments Fits well It fits well, so I weld it meticulously , except for the oven and the wood hole.

08:22 - I have to make a French socket to be combined with the pipe, but it doesn’t fit because of the difference Cut a little bit and reprocess it so that the flue can fit.

09:14 - There is nothing easy to do Tighten with a clamp to check the clearance and then weld The protruding part was trimmed with a grinder Marking the place for the French socket Turn it over and make the legs of the inner stove When it’s all cut, you’ll have to weld it.

10:54 - Now drill a hole Curves are difficult to cut with a grinder, so when I cut them angled, it is easy and fast We welded the pipe that will be the French socket prepared earlier.

11:30 - This is an iron plate. It has been processed for about 15,000 won.

11:42 - We weld the processed iron plate well Now we plan to make a door and a non-control hole in the open firewood entrance.

12:28 - After processing the iron plate, the remaining pieces, welding hinges, and stainless steel seasoning bowl were used.

12:32 - Put in the bolt and fix it with the butterfly nut I marked the spot for the unregulated hole and drilled it We welded on the back side to prevent the bolt from loosening I also attached a hinge I’m going to attach the oven handle using the remaining pieces of iron plate and round pipe.

13:40 - Welding is more convenient than you think I trimmed the handle and attached it Oven drawers must also be made using an iron plate.

14:18 - Hello hello hello hello hello last hello After checking if it fits well, I welded the folded part to increase the durability.

14:50 - And combined it with the oven handle.

15:00 - Fits well I plan to use the oven handle as an ash tray.

15:08 - This is the eye nut I bought at the bolt house I plan to use it as a handle It’s almost the end now I’m planning to make a firewood rack by using an iron plate.

15:46 - Iron fragments splattered in my eyes while trimming.

16:44 - Safety equipment is essential when working This is my first time using 8mm steel bar I’m going to cut a little bit of steel bar and make a hinge for the firewood rack.

17:00 - After confirming that it fits well, we weld It works well. I put another set in the same way.

17:34 - We weld the steel bar to the steel plate.

17:48 - I think welding is more convenient than I thought Now only heat-resistant paint remains I also put firewood The firewood drying rack works well. This is the Sinseon-ro bowl used to make the inner stove last time.

18:42 - I’m going to enjoy seasonal cuisine. I’m looking forward to seeing what the new oven looks like.

18:48 - The firewood doorways and uncontrolled holes seem to be well made.

18:56 - The legs of an unused camping table were used as the legs of the inner stove.

19:06 - That’s it for making a square pipe inner stove aka indoor firewood stove.

19:12 - If you are curious about how to use it, please watch this video until the end.

19:16 - The firewood drying rack is useful.

19:42 - I think it’s well made. I ’ll put firewood and light it. It’s a very exciting moment.

19:48 - I love the logo The length of the pipe is about 3m.

20:12 - The sun goes down and the weather outside is chilly, but the inside is warm thanks to the square pipe inner stove Refill the firewood and take a break Did you have a good christmas I plan to make baked sweet potatoes as a snack When I go camping, I always leave food.

21:30 - I am going to have my own time with these leftovers Using the oven I try to plate the fruit again This is my favorite salmon head or salmon head It’s because it’s large in quantity and tastes great for the incredibly low price.

22:20 - In the meantime, cooking was uncomfortable, so I put it off, but I have an oven so I’ll try It also replenishes firewood I plan to eat raw salmon that I prepared while the salmon and fried rice are cooking This is a figure that came with a beer and as a free gift.

23:58 - I took it out because I was bored. How do you do it Sorry Take a drink, I drink a cup of salty you can not Finally, the food that went into the oven is finished The taste is excellent You worked hard again today.

25:10 - Put the burrito prepared the next day in the oven Even in sub-zero weather last night, thanks to each pipe inner stove, I was able to sleep warmly.

25:34 - I also boiled one ramen Eggs and cheese are essential I prepared ramen sausage britto salmon head for breakfast I couldn’t stand it. After talking about it for a while, I made roasted sweet potatoes for snacks.

26:10 - Both the visual and the taste are great Video I prepared I will Thanks haejusimyeon subscriptions and likes alarm setting here bye.