TORO eFLEX Greensmaster 2100 - mein Profi Spindelmäher ist so gut wie fertig!

[Music] Yes dear lawn freaks, the Lawnfreak has completely failed here. I am firmly convinced that this is the soil we have taken there. The topsoil that was under the grass clippings, and the grass clippings that really acidified. It will be really, really manured, and it will all have penetrated the ground. I can only imagine it. You should actually have a soil analysis of the stuff done here.

00:57 - We’re going to start a second experiment with potting soil, and then we’ll see how it looks. So really high quality potting soil instead of this topsoil that we have lying around there. And you will see it. But now let’s do something different. We will now continue to screw, screw my eFlex together. I already screwed the first frame parts onto the aluminum housing. Sensational! Stay tuned until soon. Yes, here is the framework. What is ticking here? Stop ticking. So here you see the beautiful drive housing, connected to the side flange here, below the shaft and I have already screwed on the first beautiful freshly painted steel parts.

02:08 - At the back this connecting strut here, and it is making great strides. Cool So, my famous “so”. Now I’m thinking… oh that’s not possible… The question is: Do we finish the spindle first and put the spindle on it again? So that the case is nice and solid here. Later I can take the spindle down again. That would be one possibility. Let’s do that, why not that. I hurt myself so stupidly here, unfortunately I didn’t wear my gloves. Then I have here with this wire brush, which I put on my flex, hewn over here once, and it heals very badly because it is a very stupid place. I have to watch out a little more now. They come in here. Anticorite well… the rod like that… now I have to remove the bushings down here. Carefully separate the last four bushings. I left it in there.

04:00 - I said they should stay in there so that the seat of the bushings is not damaged as much. So that they stay nice and tight. And I actually still have four bushings. Look how nice they sit. Yes, great nice tight… Very nice! These are the new ones. I would have to use a thicker piece of wood. I know you see nothing now. None of that helps. It is suspended a little bit pendulum, it is not even now. Awesome Good I have to hold up now, I’ll put a cloth between them. Where is it beating? Ahh there it strikes against. OK We don’t want that.

06:22 - cool Other side chatting Then we could put the spindle on it. To do this, it has to tip it over here and hold it here. And now it’s rolled in so and then put this in here. wonderful… wonderful… That’s what it looks like. So freaks, that looks incredible. total cool… Right here at the point because the case is a bit incorporated, because it is always beaten here when you take it up. But now there is almost an inch of air that means through the whole play what was in here the thing has come right against. And that is no longer the case.

08:08 - great That looks so cool now out! Yes Holy cow! yes nice… So now we’re going to add the bracket to the back. easy to hold together… stick together here… exactly We can of course also… that’s a bit stupid… She: Set a level? He: Yes, that’s what these markings are for. Now let’s do exactly… Exactly! First line… I think it lasts that way. Hello dear lawn freaks, there are only dramas for the Lawnfreak. It’s insane, I can’t believe it. I deleted a video I wanted to show you the assembly of the eFlex until the end, and then I delete a video. And now it’s almost done. I am so sorry. There it is, almost done. We’ll get it out now. Glorious light here, glorious…

10:47 - Drum roll Yes dear lawn freaks, that’s my eFlex. Almost done, there are still a few little things missing, which we are going to add right now. And then the spindle still has to be ground, and then I can mow for the first time. The case is still dirty, I have to go back to the case. The battery pack is not fully screwed in here either. And it’s got some dirt, it’s already a little dirty, just from standing around. madness But it looks really, really, really, really good. amazing What is really cool freaks is here to loosen the spindle, you really just loosen the two screws, then you can take it off solve even more… then he falls on the back, and you can pull the spindle out. It’s so awesome. Now the spindle comes back on the workbench.

12:58 - So freaks, now there’s a rubber ring on it, it comes on here to keep this camp. Such a fat rubber ring, and it just presses against the housing. And then it’s good. Of course you have to fumble the ring properly. It was a super smart idea to grease this ring. Now the screw comes in. There the screw in, perfect freaks. Something fell down again. Naturally… The screw comes in here… there comes a thick one and there comes a thin one… Now I have to fumble for the mother behind here. This is a bit fiddly, I was afraid that I could get it in at all… so… there it is. So freaks, here is this feather in between, it just lies in between, it has a small plastic guide here. That’s all… then you just put it in between. There is just a little screw in there. The main thing is that this earring fits properly. It fits there… I screw it up first… tighten evenly… not too tight… because then comes loose… Perfect! Perfect length the screws. enough… There is the gear ratio. I want to let it run as slowly as possible so red is in position A.

16:19 - Red in position A, the question now is whether I… the small key is missing… there has to be some anticorite… very important… zack I’m turning the wheel now because it’s pretty worn on one side, and that’s why I let the timing belt run again on the slightly less closed side. Now comes the right Allen screw… tighten… don’t tighten too tight… White is that… that comes in position C the wheel… I also put that the other way around… Can you add a little anticorite… can’t hurt… very good… let’s aligned here… wonderful here… the third wheel Black in the middle. I agree And so it should run particularly slowly. right… we turn it the other way around… a dream it does not tighten… that is interesting… it does not tighten… Why doesn’t it tighten? Very good, it only runs with it. Good… It’s a bit further out. It doesn’t go any further. I could pull it out a bit, of course I can do that. That is not so wrong.

19:31 - Then I pull it out a bit, that they all run nicely on one level. It’s actually true… I know I’m always in front of my arms, I have to put the camera somewhere else. I can cut it out. And these can also get out a bit, that’s not wrong either. That the timing belt runs nicely in the middle, freaks. That’s better. Now put the timing belt on it, loosen the screw a little bit like this. it do not want… So now up the timing belt… come on.. very nice… is moving in… Insane, I still have to tighten… Cool… fantastic… and now we can close. gorgeous… gorgeous very nice, done! 35.7…. 35 kg I don’t believe it…

22:54 - She: Did you lift well off your knees? He: I don’t think so. finished great So dear cylinder mower freaks that’s it for today with the eFlex. I think that was the last video here of assembling my eFlex. Almost everything is done now. I still have a counterweight over there that I have to screw on. I haven’t done that anymore. Otherwise it is completely assembled, the spindle runs as you have seen. And now it has to be ground, because without a ground spindle, no cylinder mower cuts. And that’s a complex story, the spindle grind. That is why we will have it done by a professional. Hopefully there will be a nice video about that. So stay tuned, subscribe to me, and you’ll know when I upload a new video.

24:55 - I look forward to you and the next videos. Your Lawnfreak bye .