Мини Дом Плоская крыша Гидроизоляция Монтаж пластиковых окон Вентилируемый фасад - сайдинг

250-270 kilograms it weighs… Essentially nothing else could be done There will be emptiness here, we will sew it differently Warm - yes All cut to size undercutting, forcutting - everything is done Can’t cut with a grinder this metal because it is set on fire We placed a full bedroom with a large mattress Water is flowing, right? Yes The most important thing that I would like to say We make several similar houses exclusively for your own use Accordingly, we are not looking for the cheapest materials We are not trying to save on structure We are not trying to do it as quickly as possible. There are so many people in the frame because we are collecting this project at an existing facility which employs more than 30 people And so we do it for fun we do this, we can say in our free time The number of people who are at the moment That is, this is such a project that was born among a team of builders And we make it, so do not need to look at it as a kind of business project no need to look at it as how you should do it We tell a story about ourselves Thank you all for your understanding Third episode The first thing we did after our frame was standed up which we painted Started laying floors used 15th moisture resistant plywood It was countersinked and screwed to prof pipes Cut out our plywood And we will already fully install them They are already cut all in size undercutting, forcutting - everything is done And we put them in place Apply polyurethane sealant We create a damper between the metal and our waterproof plywood Just do not pull, immediately, raise higher Here’s, that’s all Well, it press against, where higher Kitchens, order by kitchens Two kitchens said, we take two kitchens? Is it yesterday’s? (three minimum) Fuck it Broke Drill diameter - 5 mm, screw - 4.2 Voila To drown down the hat we countersink fuck After we painted the frame we started doing different parts That is, began to make the facade, did all the adjacencies, made angular planks set the starting bars foamed angled planks to it won’t strum, to it will tougher Initially, we had a professional sheet in the project Then we thought about something else In the end, we decided on such a metal good siding At the moment, we decided to use black siding That so, stylish story If anyone is wondering why we painted red just because we wanted We decided to weigh how much our facade weighs Because in the technical specifications we have not found this anywhere We decided to do it empirically We have scales We, it turns out, are weighed without anything else and then with a strip 67 Yes, I am such thinman 2,3 kg, right? each weighs 2,3 kg And we have 110 of them Accordingly, this is approximately 250-270 kg our this facade weighs much Today we started preparing mortgages for air conditioning They will already be installed at the finish stage When already our entire facade - siding will be already assembled We welded a thread on a professional pipe Put it behind the porch with our boiled frame We will make a compensation nut I do not know how to call it We will get the distance to the back of our facade So that when we put the mounting bracket for the blocks, we do not crush our facade After we fixed the metal on the roof to the rivets and it was a blunder It was not necessary to fix by rivets, because they let water through very much Despite the fact that they hold it tight, regarding screws Well, as always, we wanted the best, but it turned out as always Then we set about shaping the roof and here our first problems began We used the 0.5th galvanized sheet which we waterproofed on both sides we kind of smarted up So, we began to fasten it simply to these reciprocal slats Which we thought kind a in advance First mistake These slats, they took a place And we, instead of getting our ramp, which we had We got some such dimples This is a design error that we did not take into account the facade slats But and this is not the main problem The main problem is that we decided to play smart again And riveted with rivets The rivets problem is as follows They flow They not only flow In the place where they flow, they also flow inside the prof pipe (No) Water is flowing, right? Yes Well, wait, you think it then leaked, right? That is, we are making holes now simply and looking, right? Yes We drilled, removed moisture from there and so on, but that was much later That is, we spotted it a little later, when it began to rain In short, we have a state of emergency Our whole masterpiece has flowed In short, this is what I talked about That we hurried Saving is such a story when it all the same backfire That is, if there is any price that it costs One way or another, with other technologies, these, you still spend these money We began to think how to waterproof it At first we just made waterproofing The membrane was very cool waterproofing In fact, the membrane is like rubber It reaches, play, that is, a cool thing But anyway, for this membrane you need some basis anyway Because it doesn’t fill any big gaps, holes and the rest, here In short, we used the 0.5th galvanized metal All junktures, all joints we cram and smeared with rubber sealant Sometimes you do right and good right away And sometimes spend a bunch of nerves and the same money And here it is up to everyone to decide in their own way Right, Sery? Of course And even we fell for it We just didn’t think to be honest We just didn’t think in a hurry, we decided it too quickly This knot was drawn The roof But we were wrong Only in one place, Sery? No, it won’t flow here, Sery, she’s got a bias here It turns out that we riveted everything, we used a 20x40 rail Again, in order to unload the structure To make it a little ligther There’s also actually a mistake But, everything comes with experience It’s necessary to mow it somehow, you know, that not we are there…

10:20 - Why not we? We Why not we? Did we mess up? Mess up The floor was wet, the moisture settled We came in the morning, thought it was condensate That’s all, decided, removed We screwed up with the roof too, right?) And we decided to exclude it In short, the entire container is a solid cheek Yes The only thing that we did normal was that we welded a frame Well, it’ll probably be slow Oh, it’s not a fact What have we done next After we closed this first, let’s say, part We began to seal all these rivets with waterproofing tape And that was also a big mistake Pipes got water There is water inside them, you know Well, until the rivets were still not closed Through the rivets it got, through the… Well, that is, now we need to make 5-6 holes, let it dry Here it is, well, water will come out More in the corners it, either way So, say that we had a lot of problems with waterproofing - say nothing First, we closed the facade again So that nothing drips without waterproofing Then, we glue, let’s say, the first layer of the mesh And by this cell 5 by 5, it will spread less And we will make such a waterproofing carpet completely again This I am sure will help But, for some reason, we came to this after a lot of iterations In general, do everything right the first time And in the end we did the following on the roof We completely covered it with a tytan’s waterproofing membrane In the bucket it’s pretty pretty cool stuff That is, he is, let’s say, rubber, liquid rubber Very cool stuff But anyway, even with this material the first time we did not manage to remove all our jambs Because we made a pool That is, we had to waterproof the roof very well Roughly speaking, we made a roof pool Then, after we covered the roof We became… The wind bars were ready These reciprocal slats, let’s say, were already ready around the perimeter We began to strengthen our facade Everything went according to our plan, as we thought The only problem is that we chose the most beautiful facade in our opinion Not just beautiful, but all such facades, they are ventilated facades And we want to get a sandwich In order to make a sandwich panel from a ventilated facade We spent a lot of iterations But in fact, there was no other option To achieve a similar appearance It was extremely difficult, a very difficult task Accordingly, all the corners besides the fact that we foamed them inside We still had to insert cut polystyrene inside by the tire, exactly the same And all this go through a special polyurethane roofing sealant We got here pretty much this, some technological adjoining part Let’s see how it behaves a little further We’ll foam it all and cover with membranes and plywood That is, we want to achieve such a sandwich, let’s say But for this to work, we need to waterproof the ventilated facade And this is a big, big problem Yes, it looks beautiful, but extremely, extremely difficult to perform PCST is a window junction So that the foam does not fall below the profile level Because water can stand in the bar And the foam, it drags That is, we make such a hydrobarrier which… To make waterproofing we glue PCST, it expands it we make waterproofing from above and continue to foam And then we get 60 mm by 90 we, it turns out, glue it here And we get 60 mm of air so that it does not accumulate, well, let’s say, any moisture And it works the way we planned It’s raining right now and you see, we have drilled holes And that’s how it works That is, we put a PCST inside Here we have an air gap By the way, like foam and stone wool, and any other such insulation it is hygroscopic, it will pull moisture The air is perfect for that place To make the waterproofing circuit we glue PCST And we make waterproofing on top thereby we get a very correct adjacency Further we have already inserted a heater And it turns out that during the rain it can’t Well, because it would be hygroscopic if there were foam and any insulation It is hygroscopic, moisture would have risen there Well, we did in such a bad way And these our junctions look very good And now it flows inside And flows down below our holes Nothing else could be done Well, there are many variates of material But this is the only material that is lightweight, which suits us by and large Although this is a ventilated facade, well, in fact But we made it as unventilated That is, we accordingly got a lot of adjacencies which we needed to seal Then we cut holes in the facade to lift the container Started to mount corners For our siding (here are our corners) And the roof was laid And now we need to cut to mount the siding itself We need to make holes to get to our ears For which we will cling and transport our house Now, now we will cut them Probably not to saw, but to cut You can’t cut this metal with a grinder Because he is set on fire And the corrosion begins to grow and begins to rot How to cling here And we’ll probably come up with something that we’ll additionally insert there so that the ear is imported And carry it all with you and hook for it Because of the dimensions, we can’t take anything out here to hook on this side And if we hook on the other side, we will simply arch this part of the roof and corner Therefore, we will come up with something, weld, digest Everything is still under development This is a gain edge If here, weld, for example, vertical seams remove these horizontal and leave vertical What happens when it loaded? This our welding, it’ll just burst Top down (will break) Yes, it will break And where is this one to break? It has very big square It will be worse than pouring here? (It will be worse, yes) We will weaken this metal Also places that needed to be waterproofed That is, with waterproofing, we really messed up And in general with the whole roof cake, namely the roof We hurried, we did it for the first time And a lot of mistakes were made at the time of design Because until you start doing, you cannot go deeper Yes, we have a pretty deep project Nevertheless, this is very small. That is, any project is always being finalized It doesn’t matter, it’s the repair of an apartment, a house, the construction of such a mini-house It is always processed along the way We made another mistake, we hurried We decided to do the wires in the roof layer Although initially we wanted, we deliberately left a place for all our communication it concerns electrical installation, it went sideways under the kitchen, let’s say Under our furniture But for some reason we decided to make a few outlets And our work went in the evening, that was night And we…

18:04 - Now there will be a brief analysis of the draft stage I want to say right away: don’t be scared But in this room, despite the fact that it is only 16 squares on the floor We placed a full-fledged office with two workplaces We placed a full bedroom with a large mattress We placed here a full kitchen with an oven, a refrigerator and a bunch of other peripherals We placed a drain pump here We fit a full boiler of 80 liters here And full (not clear) We placed a washing machine and a dryer here We placed the warm floor here And very modern lighting We also fit air filtration and air conditioning here And this is all true We will start engineering soon There will be general trash For many people, their hair will stand on end Subscribe to the channel, click the bell button, like button And all these things And do not forget that we have instagram On Instagram, content comes out much more often And there we upload a lot in stories, we have all sorts of different funny content e have really interesting and useful things And we have a whole on Instagram, you can say, a whole community of people who write comments there, do reposts, etc. So whoever does not yet have an instagram and a person thinks that this instagram is for girls, you are very mistaken There are a lot of useful building content The fact that we decided to change siding to corrugated board and push our crosses inside the structure It led us to the next construct, which, by the way, turned out to be very technological We got 16 mm of additional insulation From the facade Plus we removed the cold bridges from 60 to 40 of our crosses That is, we pushed them inside And we got 16 mm, then 20 mm - a pipe of 20 by 20, then 60, 40 mm is still the next Total, when everything here is foamy, we will have no cold bridges, nothing We will have such a sandwich panel, even such We are now warming the bottom contour of our home And we made… a decision… And we made a decision - to use penoplex for insulation In two layers with overlap Between layers and in order to fix the first layer we use tytan Special adhesive for thermal insulation A little bit about the principle of how glue works Even with the strongest winds, now we can apply it to penoplex and stick it And we glue in two stages The first stage is with us - we stick 20 mm between the lags And the second lap like this, we stick another 50 mm on top to avoid all cold bridges The manufacturer writes that the glue itself eliminates bridges of cold But we still do overlap between the two layers Sery, and there will be a lock, right? Yes I thought it couldn’t hold it, although it’s necessary to fix it And then we will not sleep peacefully As a heater, we chose polystyrene foam, it is on the floor and on the ceiling That is, because we had a certain step Foaming there, onrfoaming some kind of insulation, we did not see the point Inconveniently, it’s from below, well, there’s no point in short We just took polystyrene foam and started cutting it To cut it we used a submersible saw Yes, we used a submersible saw, so what? Why not? It’s convenient, it’s fast, it’s cool, it’s all right By what else to cut? Of course there are special saws, but we do not have such saws that cut polystyrene foam Here, we just used a submersible saw That is, we insulated 70 mm from the bottom, it turns out 50 and 20 more And fastened additionally on washers, on screws through washers special for expanded polystyrene And also attached to the glue, a special adhesive for expanded polystyrene Now we fix the second layer On the paddles - this is fixation and fixation plus glue Fasten on the paddles plus glue Perfect cut Foam it, Sanya Huh? Sanya if foaming it, I am fasten it, Sery if sawing I’m also 24 and I’m not married In all containers that, in principle, did not suit us In all there was used minwool - mineral wool Since they had very poor waterproofing, it got very wet, gaining moisture Well, in principle, this did not suit us There is a likelihood of the same: that will gain moisture and so that this is not To not lose heat That is, mineral wool, when it picks up moisture, it ceases to carry its functions And there’s no penoplex, penoplex is not picking up moisture We insulated the floor, we used the same polystyrene For what reason? That it is not hygroscopic material Still, he will stand on the floor We used 50 mm and 20 That is, we first made 20, then with an overlap we made 50 All this was fixed on foam-glue Plus special washers for polystyrene We have chosen the length of the self-tapping screw so that it fits 25-30% into our plywood Right now, for the going of business, it’s going to go like this and here it’s going to turn on exactly this blanket and it’ll pass And here the void will remain There will be emptiness here, we will sew it differently Warm - yes But to profile, if we look at the cut from above, right? That plywood, now this plywood fits and it fits clearly with these mortgages That is, it fits clearly flush You know? And all and that is, then already, when there will be a wall, a partition, something else Here we are already our independent story and further from it we will release there The wall will be here, and we’ll start to narrow it down So we got an empty frame? It will turn out now with a little emptiness That distance is 286 You can just go in, these mortgages, what we have, just stupidly leave them, go around and leave the profile And then sew on top? Why do we need a profile here? Why do we need that? Yes there, just forget, maybe we will do more there, maybe we will need something there But will it close in the end? It all closes in the end, generally the bar It will eventually close with one bar and it will be even lower than the main whole ceiling Are we leaving? -And we finished everything here? -Well yes Proceed to the installation of our ceiling We use a 60 by 27 profile and a 27 by 28 guide Everywhere we use Bacons Ban On suspensions, on guides, everywhere adjoining metal, everywhere we use it Now we fix the suspensions in the middle We will put a guiding profile around the perimeter and roll over the profile The hangers we have are approximately 1100 mm Single-level wireframe We decided to fill profile with foam It will prevent the formation of condensation, perhaps, but this is not accurate And will give additional sound insulation When closing doors, moving So that our noise is not transmitted to the ceiling No, look, look Now we, for example, set the bar here We have there, there’s even already somewhere around 35, but here all 40 are probably, how many are here? Well, idk Well, how much is there? No, there are also 40 No fuck That’s how much right now, measure 50 Well, here 30… 40 with some We got windows yesterday Not mega-cool packed, but what I liked the most was the handles Carry handles are super comfortable That is, installers can easily take it The biggest problem is dragging them Who invented these little handles for which you can raise windows - it’s just very cool We have windows at once on our two mini-houses And our second layout is slightly different from the one we are doing this time Since we are doing this project for ourselves We ordered windows in black that is, with the paint and chose the manufacturer - it is a window Voronezh’s plant These guys put me windows on several objects These are super cool packaged guys And now we choose exactly the layout that we ordered exactly the opening mechanisms we show a little later Here we take it and carry it We argued for a long time about how we will install windows And in the end we came to this conclusion Vanya, how will we install the windows? In short, we will put on the corners We will put on the corners, right now you will see To the corners, yes, we will press the windows to the quarters Special adhesive glue We made special quarters, right now we’ll show And, it turns out, we will go through everything with roofing sealant We put it in quarters with a sealant, that is, a PCST, we will not have all of this Immediately put on sealant I don’t know, hi haters, is it right or not Now many will write in the comments: Ruvim, why the heck are you gluing tape on the slopes? Now I want to talk a little bit about our junction of the slope What have we done? We welded a quarter of the 20x20 profile Then this quarter was framed by corners At what these corners are not from the system, we stuck them so to speak And the most difficult thing was to stick these slopes to the 20x20 profile Because they puffed up We made whole such spacers, pasted on glue We glue the window into our quarter, that is, well, as a junction And by the quarter we will go through roofing sealant rubber And everything else - watch more video As you already noticed, we ordered windows with non-standard opening of the sash The door opens from the center to the edge In order to save a place, which is already not very much When ventilating the room, we will not walk and fight against this sash, pass it sideways The only thing, but this is probably more plus than minus I thought the profile would be 50 mm, and it turned out to be 70 They put in 3 glasses Windows are energy-efficient, with an MFP film, with argon inside, with a reinforcement of 2 mm, with accessoriesитальянской Well, there was Ruvim with you Meet me on the other side of the screen Bye everyone! That’s all, good .