IMPRIMANTE 3D Easythreed X1 Mon Teste & Avis

Hello and welcome to this first video during containment, I say the first because I don’t know how long it will last. Today we have a 3D printer and let’s face it, there are a lot of unnecessary things you could buy for $ 99 right now So today we have this famous 3D printer from Easythreed, from China… don’t worry they are located in Shenzhen. And so we are going to try it, the question is. Does it really work is it worth ninety-nine dollars and most importantly does it deserve to be called a 3D printer, you should stay to find out but above all keep an open mind for this video especially until the end But before we go any further, a surprise awaits you at the end of this video, then I ask you to explode the button I like thoroughly So the box of the 3D printer is quite small and well packaged inside you will find a line sample a USB cable the power cable and a micro SD card as well as the instructions and a print copy, it also contains some long screws and nuts a screwdriver and the small spool pin of the printer Printer arrives with three pieces, all of which are wired from the start composed at the base with a removable magnetic construction plate the gantry and the control unit, you will also find a power box and a USB cable, the assembly process consists of running the disconnected cable only through a hole sliding the gantry in place, tighten two long screws with nuts to secure it in place and connect the stepper motor to the z-axis. the control box has four buttons a home button that houses only the z-axis a minus button and a plus button that control the charge and charge the operation of the filament and a play button that serves as start and pause for printing by pressing the plus sign the machine will start to heat at the end, now while heating it will start flashing quickly and once it reaches the ideal temperature the flashing slows down and the extractor starts to push the filament of course we must not forget the SD card and press play, I was really surprised because she started printing much better than expected, but honestly after getting it i didn’t expect such a result If not I was very supposedly surprised with the micro SD card which contained a copy of several samples which actually allows the printing of several models to start testing at the beginning.

04:16 - And at first glance I was not really looking for good print quality, especially because it doesn’t have a cooling fan, but finally she printed pretty well, now the downside and not having a fan part this does not allow the print finish Returning to the SD card, when you drop a file on the SD card, you just put it in the main g-code directory that you insert into the printer and so the printer knows what to do next again she printed and without touching the print settings now if you follow this far and you are intrigued by this printer, because at $ 99, this little machine is still a lot of fun. the control unit contains a motherboard, I initially thought it was a big technological table, but I know the card is actually used on larger 3D printers because this is a reduced version, in fact, after checking it has a location for a Wi-Fi extension but above all a connector for the cooling fan, so for hackers you can add them. But above all keep in mind that this is a cheap 3D printer which not only works but it works really well it turned out so much better than I expected I decided to start a more complex printing, knowing that the printing speed is not more than 30 millimeters per second, so it will be slow, which is expected as a printer structure because the components do not allow higher speeds. After more than 50% printing, the printer has had a printing lag and start doing anything, honestly i don’t know if this is due to the 3D model or to the printer, but since the filament sample is not long enough, I did not have the opportunity to do several tests At the same time, after several intensive tests to see how the printing goes with more results. The printer was more impressive considering the profiles which requires a little more work even more than normal because you know the stepper motor system which works so the hot end for printing, since two out of three tests have been successfully printed That said it remains a product probably better than if you take a 3D pen this printer remains more efficient.

06:49 - A very important thing for this printer since it could certainly also target children or the younger generation, security must therefore be paramount that’s why the printer has some kind of security device which cuts the power at the hot end when the thermistor does not read the temperature correctly which is a good thing, it also prevents the filament puller from spinning once the thermistor is reconnected and the temperature goes up and the engine starts running again, now if this disconnects if a printing fault occurs the hot end cools again the extractor stops rotating but the printer continues its printing movement without actually extracting, I’m happy to see that there are some adequate security features, I must say when I received this printer, Honestly, I didn’t think I was going to make a video on it with all this information, personally I was impressed and I really like this machine, I will share photos of what I will be able to test as an impression, you could tell me what you think. but not everyone can afford to buy a 3D printer with a very high price. not everyone wants to spend more than $ 100 on a product, but with this printer you will be able to start in 3D printing and with the least possible cost In the end you can afford to offer it even as gifts. This machine opens the possibilities for those who want to get their hands in the dough in 3D printing, we will say that it is an initiation product in a few weeks, if not a few days, but most importantly if you want to give this to your children, you just copy a template to put it on the SD card and give it to them, all they have to do is just insert the card into the 3D printer so I agree without hesitation and it really makes me excited for the future because you can imagine in a year what we can get in terms of 3D, we are even now starting to build buildings with 3D printing, so imagine Finally the printing capacity for this price remains excellent, it is another segment of the market that can be completed and can still develop at the community level if you have any questions, leave them in the comments section below, I will leave a link in the description of the video of the Easythreed X1 in case you are interested and want more information As always make sure you like to share and subscribe for the next videos. By the next video I wish you a good containment Stay at home and see you soon for new video Ah I forgot, So before I finish, I have a little surprise for you, we got 10,000 subscribers, again I thank everyone who is interested in the channel from far or near, and for this occasion I will be able to trigger a competition to win this 3D printer, for this you just need this video to reach 1000 like nothing to complicate; so feel free to like and share with your friends.

10:07 - so that i can trigger this contest for you Until then I tell you how well you and your families are Ciao.